{"title":"AC - Sealer","description":"","products":[{"product_id":"ac-the-art-of-concrete-18-cure-seal-5-gallon","title":"AC - the art of concrete 20 Percent Sealer 5 Gallon","description":"\u003cp\u003e\u003cb\u003eACPRODUCT DESCRIPTION AND USES\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 20% Sealer is a VOC Compliant, premium high quality, durable, abrasion resistant, single component 20% acrylic solids sealer for new or existing concrete and masonry. The 20% solids content provides a UV stable high-gloss finish that will colour enhance the concrete surface. AC the art of concrete 20% Sealer  is ideal for use on concrete that is at least 28 days old. This product may be used on all concrete no matter the finish. Concrete may be smooth or rough finished and may include:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eConcrete Flatwork\u003c\/li\u003e\n\u003cli\u003eLight Commercial\u003c\/li\u003e\n\u003cli\u003eArchitectural Concrete\u003c\/li\u003e\n\u003cli\u003eBrick\u003c\/li\u003e\n\u003cli\u003eStone\u003c\/li\u003e\n\u003cli\u003ePrecast concrete \u0026amp; walls\u003c\/li\u003e\n\u003cli\u003eResidential walkways, driveways and patios\u003c\/li\u003e\n\u003cli\u003eConcrete curbing and borders\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003ePACKAGING\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 20% Sealer is available in 18.9L containers and is a ready to use formulation.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCOVERAGE\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 20% Sealer will cover 150 - 200 square feet per gallon. (700-1000 square feet per 5 gallon pail) depending on the surface finish and porosity of the substrate.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003ePLANNING AND SURFACE PREP\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 20% Sealer can be applied to concrete that is at least 28 days old. Finish trowel the concrete and allow surface water to dissipate completely. Use a low pressure sprayer (20 - 30 lbs.) and apply a uniform coat at a rate of coverage as specified below. Avoid heavy accumulations. A second coat may be necessary where concrete is very porous and where absorption is very rapid. An additional coat may be applied after first coat is tack free.\u003c\/p\u003e\n\u003cp\u003eBroomed Concrete - 250-350 square feet per gallon.\u003c\/p\u003e\n\u003cp\u003eTroweled Concrete - 300-450 square feet per gallon.\u003c\/p\u003e\n\u003cp\u003eDustproof Seal - 250-400 square feet per gallon.\u003c\/p\u003e\n\u003cp\u003eSecond Coat - 300-600 square feet per gallon.\u003c\/p\u003e\n\u003cp\u003e\u003ci\u003e(These coverage rates are approximations only. Many factors will affect coverage rates.  These will include, but are not limited to: surface texture, porosity of the concrete, and weather conditions.)\u003c\/i\u003e\u003c\/p\u003e\n\u003cp\u003eCLEAN AND DRY: AC the art of concrete 20% Sealer may be applied on fully cured concrete. All surfaces must be clean and free of all contaminants such as dust, dirt, oils, efflorescence, grease, paint, glue, rust, algae, mildew, non-acrylic coatings and any other foreign matter that may be a bond breaker. Allow 24 hours for the substrate to dry before applying.\u003c\/p\u003e\n\u003cp\u003eSURFACE CONDITION: All concrete substrates should be sound with no hollow spots, scaling or flaking.  All delaminated material should be completely removed. Shot blasting, grinding and\/or scarifying should be done in those areas.\u003c\/p\u003e\n\u003cp\u003eMASKING: All areas that are not intended to receive AC the art of concrete 20% Sealer, should be protected by masking. Protect vegetation and landscaping.\u003c\/p\u003e\n\u003cp\u003eTOUCH-UP: Finish all touch-up work prior to sealing. This includes cleaning, detailing and colouring.\u003c\/p\u003e\n\u003cp\u003ePLANNING: The substrate must be dry for all steps, during and 24 hours after application. Application of AC the art of concrete 20% Sealer should be avoided on extremely cold or hot days (if the temperature will not be within the aforementioned ranges for 12-24 hours after application). Do not apply if rain, snow or hail is being forecast for the 24 hour period after application.\u003c\/p\u003e\n\u003cp\u003eBoth the concrete and the ambient air temperature should be between 10°C and 32°C during application.\u003c\/p\u003e\n\u003cp\u003eMIXING: This product does not need mixing. It is ready for use and no dilution is necessary.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eAPPLICATION: \u003c\/b\u003eAC the art of concrete 20% Sealer will darken concrete.\u003c\/p\u003e\n\u003cp\u003eROLLING:\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eUse a bucket grid or metal paint tray to ensure application of a thin film. (No puddling of product)\u003c\/li\u003e\n\u003cli\u003eRoller sleeves will require a solvent resistant core.\u003c\/li\u003e\n\u003cli\u003eThickness of roller sleeve will depend on the substrate being covered. A rougher surface will require a longer nap. A smooth cementitious surface such as a garage floor will require a 6 mil roller sleeve. Broom finished concrete, light exposed aggregate or a shallow stamped concrete will require a 10 mill roller sleeve. Deep exposed aggregate or a deep stamped concrete will require a 19 mil roller sleeve.\u003c\/li\u003e\n\u003cli\u003eBack rolling will help to eliminate roller lines. Back rolling should be done perpendicular to application.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eSPRAYING:\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eUse a low pressure sprayer (20 - 30 lbs.) and apply a uniform coat at a rate of coverage as specified below. Avoid heavy accumulations. A second coat may be necessary where concrete is very porous and where absorption is very rapid. An additional coat may be applied after first coat is tack free.\u003c\/li\u003e\n\u003cli\u003eA single coat is usually sufficient for most applications. However, if your substrate looks “blotchy or uneven” after the first coat, a second coat may be applied. Wait for the first coat to dry sufficiently so that you may walk on it. If a second coat is required, it can be applied exactly as the first coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003ePlease allow the proper amount of cure time after applying sealer. For foot traffic allow 24 hours. For vehicular traffic allow 72 hours.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCLEAN UP:\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eBefore AC the art of concrete 20% Sealer dries, solvents such as Xylene or Acetone may be used.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eSTORAGE AND CAUTIONS:\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 20% Sealer is flammable. Avoid heat sources, spark, electric tools and open flame sources. Store in a cool dry area out of direct sunlight. Shelf life under normal recommended conditions is 2 years. Store in sealed containers. Keep area well ventilated. Do not allow to freeze. \u003cb\u003eINHALATION: \u003c\/b\u003eUse approved NIOSH PPE (Respirator for organic vapours). \u003cb\u003eSKIN CONTACT: \u003c\/b\u003eMay cause irritation.  Remove all contaminated clothing and wash before reusing. Wash affected skin area with soap and water. If symptoms persist, seek medical attention.  \u003cb\u003eEYE CONTACT: \u003c\/b\u003eWear eye protecting while handling product. If contact with eyes does occur, remove contact lenses (if present). Flush eyes with water or eye wash solution for 15 minutes. Seek medical Attention.  Consult the SDS sheets for further information before use of product. \u003cb\u003eKEEP OUT OF REACH OF CHILDREN.\u003c\/b\u003e\u003c\/p\u003e\n\u003cp class=\"MsoNormal\"\u003eThis Product is classified as a Hazardous Materials and needs to be shipped according to the Transportation of Dangerous Goods (TDG) shipping regulations. Because of this, extra shipping charges will be assessed due to the TDG services needed.  This product will have to be shipped on an LTL carrier that has the capabilities to carry out this service.  You will be contacted with the extra charges needed. \u003c\/p\u003e\n\u003cp\u003e DATA SHEET DOWNLOADS\u003c\/p\u003e\n\u003cp\u003e\u003ca rel=\"noopener\" href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0681\/0737\/0788\/files\/AC_20_Contractor_Grade_Sealer_400GPL_TDS.pdf?v=1744754087\" target=\"_blank\"\u003eAC - the art of concrete 20% Sealer TDS\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca rel=\"noopener\" href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0681\/0737\/0788\/files\/AC_20_Contractor_Grade_400GPL_SDS.pdf?v=1744754087\" target=\"_blank\"\u003eAC - the art of concrete 20% Cure \u0026amp; Seal SDS\u003c\/a\u003e\u003c\/p\u003e","brand":"AC the art of concrete","offers":[{"title":"Default Title","offer_id":45380203774244,"sku":"**622099","price":224.79,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0681\/0737\/0788\/files\/ACContractor205Gallon.jpg?v=1745523182"},{"product_id":"ac-the-art-of-concrete-20-sealer","title":"AC the art of concrete 20 Percent Silane 5 Gallon","description":"\u003cp\u003e\u003cb\u003ePRODUCT DESCRIPTION AND USES\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAC the art of concrete 20% Silane Penetrating Acrylic Sealer\u003c\/strong\u003e is a VOC Compliant, premium high quality, durable, abrasion resistant, single component silane Based, 20% acrylic solids sealer. This sealer is designed for use on any cementitious surface for protection and highlighting colour.\u003c\/p\u003e\n\u003cp\u003eIt is vapour permeable and will apply out of doors readily. This sealer is formulated for Canada’s extreme freeze\/thaw cycles.  Because of this sealer’s superior silane formulation, it will penetrate deeply into the concrete’s surface, therefore intensifying the bond with the concrete and slowing moisture migration and efflorescence.\u003c\/p\u003e\n\u003cp\u003eThe high quality solvents will give the user ample working time when applying AC the art of concrete 20% Penetrating Sealer. A single coat will provide protection for the concrete while providing UV protection, enhancing the beauty and colour of the concrete.\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete sealers can be used on any concrete surface including driveways, patios, walkways, stairs, garages, pool decks and even stucco.  This sealer will provide a semi-gloss finish to your concrete surface.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003ePACKAGING\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 20% Penetrating Sealer is available in 3.78L and 18.9L containers and is a ready to use formulation.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCOVERAGE\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 20% Penetrating Sealer will cover 150 - 185 square feet per gallon. (700-900 square feet per 5 gallon pail) depending on the surface finish and porosity of the substrate.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003ePLANNING AND SURFACE PREP\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 20% Penetrating Sealer must be applied to dry, clean concrete. The concrete should be fully cured (28 days or older). The concrete and ambient air temperature should be above 10°C and below 32°C.  \u003c\/p\u003e\n\u003cp\u003eThis product is flammable. If applying indoors, please turn off fuel sources such as heaters, furnaces and water heater pilot lights. Provide ventilation so that vapours do not accumulate and wear appropriate PPE (Personal Protection Equipment) such as, but not limited to: respirators, gloves and safety goggles.\u003c\/p\u003e\n\u003cp\u003eCLEAN AND DRY: All surfaces must be clean and free of all contaminants such as dust, dirt, oils, paint, glue, rust, algae, mildew, non-acrylic coatings and any other foreign matter that may be a bond breaker.\u003c\/p\u003e\n\u003cp\u003eThis should include and flaking or loose sealers from previous applications. Use of a light acid cleaner can be used for this purpose. Allow 24 hours for the substrate to dry before sealing.\u003c\/p\u003e\n\u003cp\u003eSURFACE CONDITION: All concrete substrates should be sound with no hollow spots, scaling or flaking.  All delaminated material should be completely removed. Shot blasting, grinding and\/or scarifying should be done in those areas.\u003c\/p\u003e\n\u003cp\u003eSUBSTRATE PROFILING: The Concrete substrate should be profiled according to the CSP (Concrete Surface Profile) standards of between 1 and 2.  This can be attained through mechanical means such as grinding, sand blasting or light scarifying or chemically through the use of a light cleaning acid and pressure washing.\u003c\/p\u003e\n\u003cp\u003eRECOATING:  If this sealer is being used to recoat concrete, it should only be used if the previous coating was a solvent based acrylic formula.  This product should never be applied over water based acrylics. \u003c\/p\u003e\n\u003cp\u003eIf the previous product is unknown, a xylene test (see below) may be used to determine the type. A small test area should be used to determine compatibility of solvents. If solvents are not compatible, blistering, peeling or delamination may occur.\u003c\/p\u003e\n\u003cp\u003eXYLENE TESTING (If needed): For this test, you will need Xylene, paper towel and plastic. Put a small amount of xylene on the paper towel and place that on the concrete. Cover the paper towel with plastic and allow to sit for 15 minutes. After 15 minutes, a solvent based acrylic will feel slippery. A water based acrylic will be a slimy mess that can be scraped off easily.\u003c\/p\u003e\n\u003cp\u003eMASKING: All areas that are not intended to receive AC the art of concrete 20% Penetrating Sealer, should be protected by masking. Protect vegetation and landscaping.\u003c\/p\u003e\n\u003cp\u003eTOUCH-UP: Finish all touch-up work prior to sealing. This includes cleaning, detailing and colouring.\u003c\/p\u003e\n\u003cp\u003ePLANNING: The substrate must be dry for all steps, 24 hours before, during and 24 hours after application. Application of AC the art of concrete 20% Penetrating Sealer should be avoided on extremely cold or hot days (if the temperature will not be within the aforementioned ranges for 12-24 hours after application).\u003c\/p\u003e\n\u003cp\u003eDo not apply if rain, snow or hail is being forecast for the 24 hour period after application.\u003c\/p\u003e\n\u003cp\u003eBoth the concrete and the ambient air temperature should be between 10°C and 32°C during application.\u003c\/p\u003e\n\u003cp\u003eMIXING: This product should be mixed for three minutes with a jiffy style mixer on medium speed making sure not to add air during the mixing process.  This is to make sure the matting agent is thoroughly dispersed.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eAPPLICATION:\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eROLLING:\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eUse a bucket grid or metal paint tray to ensure application of a thin film. (No puddling of product)\u003c\/li\u003e\n\u003cli\u003eRoller sleeves will require a solvent resistant core.\u003c\/li\u003e\n\u003cli\u003eThickness of roller sleeve will depend on the substrate being covered. A rougher surface will require a longer nap. A smooth cementitious surface such as a garage floor will require a 6 mil roller sleeve. Broom finished concrete, light exposed aggregate or a shallow stamped concrete will require a 10 mill roller sleeve. Deep exposed aggregate or a deep stamped concrete will require a 19 mil roller sleeve.\u003c\/li\u003e\n\u003cli\u003eBack rolling will help to eliminate roller lines. Back rolling should be done perpendicular to application.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003eSPRAYING:\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eThe airless sprayer used should be capable of spraying 0.5 gallons per minute (GPM) with a 65° fan tip size of between .015 to .019”. Maintain a wet edge between passes.\u003c\/li\u003e\n\u003cli\u003eA pump-up sprayer may also be used. The sprayer MUST be a solvent resistant sprayer. A sprayer tip of .5 gallons per minute should be sufficient to apply this product. Back-rolling may be used.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003eA single coat is usually sufficient for most applications. However, if your substrate looks “blotchy or uneven” after the first coat, a second coat may be applied.  Wait for the first coat to dry sufficiently so that you may walk on it. If a second coat is required, it can be applied exactly as the first coat.\u003c\/p\u003e\n\u003cp\u003ePlease allow the proper amount of cure time after applying sealer. For foot traffic allow 24 hours. For vehicular traffic allow 72 hours.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCLEAN UP:\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eBefore AC the art of concrete 20% Penetrating Sealer dries, solvents such as Xylene or Acetone may be used.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eSTORAGE AND CAUTIONS:\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 20% Penetrating Sealer is flammable. Avoid heat sources, spark, electric tools and open flame sources. Store in a cool dry area out of direct sunlight. Shelf life under normal recommended conditions is 2 years. Store in sealed containers. Keep area well ventilated.  \u003cb\u003eINHALATION: \u003c\/b\u003eUse approved NIOSH PPE (Respirator for organic vapours). \u003cb\u003eSKIN CONTACT: \u003c\/b\u003eMay cause irritation. \u003c\/p\u003e\n\u003cp\u003eRemove all contaminated clothing and wash before reusing. Wash affected skin area with soap and water. If symptoms persist, seek medical attention.  \u003cb\u003eEYE CONTACT: \u003c\/b\u003eWear eye protecting while handling product. If contact with eyes does occur, remove contact lenses (if present). Flush eyes with water or eye wash solution for 15 minutes. Seek medical Attention.  Consult the SDS sheets for further information before use of product. \u003cb\u003eKEEP OUT OF REACH OF CHILDREN.\u003c\/b\u003e\u003c\/p\u003e\n\u003cp class=\"MsoNormal\"\u003eThis Product is classified as a Hazardous Materials and needs to be shipped according to the Transportation of Dangerous Goods (TDG) shipping regulations. Because of this, extra shipping charges will be assessed due to the TDG services needed.  This product will have to be shipped on an LTL carrier that has the capabilities to carry out this service.  You will be contacted with the extra charges needed. \u003c\/p\u003e\n\u003cp\u003eDATA SHEET DOWNLOADS\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0681\/0737\/0788\/files\/AC_20_Silane_Sealer_400GPL_TDS.pdf?v=1744752662\" rel=\"noopener\" target=\"_blank\"\u003e\u003cspan\u003eAC the art of concrete 20% Penetrating Acrylic Sealer TDS\u003c\/span\u003e\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0681\/0737\/0788\/files\/AC_20_Silane_Sealer_400GPL_SDS.pdf?v=1744752662\" rel=\"noopener\" target=\"_blank\"\u003e\u003cspan\u003eAC the art of concrete 20% Penetrating Acrylic Sealer SDS\u003c\/span\u003e\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e","brand":"AC the art of concrete","offers":[{"title":"Default Title","offer_id":45380316987684,"sku":"**209115","price":332.79,"currency_code":"CAD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0681\/0737\/0788\/files\/ACSilane205Gallon_cc7a629d-cb52-47f9-9ef2-7fd64fb309b3.jpg?v=1745523182"},{"product_id":"ac-the-art-of-concrete-30-penetrating-acrylic-sealer","title":"AC the art of concrete 30 Percent Silane 5 Gallon","description":"\u003cp\u003e\u003cb\u003ePRODUCT DESCRIPTION AND USES\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAC the art of concrete 30% Silane Penetrating Acrylic Sealer\u003c\/strong\u003e is a VOC Compliant, premium high quality, durable, abrasion resistant, single component silane Based, 30% acrylic solids sealer. This sealer is designed for use on any cementitious surface for protection and highlighting colour.\u003c\/p\u003e\n\u003cp\u003eIt is vapour permeable and will apply out of doors readily. This sealer is formulated for Canada’s extreme freeze\/thaw cycles.  Because of this sealer’s superior silane formulation, it will penetrate deeply into the concrete’s surface, therefore intensifying the bond with the concrete and slowing moisture migration and efflorescence.\u003c\/p\u003e\n\u003cp\u003eThe high quality solvents will give the user ample working time when applying AC the art of concrete 30% Penetrating Sealer. A single coat will provide protection for the concrete while providing UV protection, enhancing the beauty and colour of the concrete.\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete sealers can be used on any concrete surface including driveways, patios, walkways, stairs, garages, pool decks and even stucco.  This sealer will provide a semi-gloss finish to your concrete surface.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003ePACKAGING\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 30% Penetrating Sealer is available in 3.78L and 18.9L containers and is a ready to use formulation.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCOVERAGE\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 30% Penetrating Sealer will cover 150 - 185 square feet per gallon. (700-900 square feet per 5 gallon pail) depending on the surface finish and porosity of the substrate.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003ePLANNING AND SURFACE PREP\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 30% Penetrating Sealer must be applied to dry, clean concrete. The concrete should be fully cured (28 days or older). The concrete and ambient air temperature should be above 10°C and below 32°C.  \u003c\/p\u003e\n\u003cp\u003eThis product is flammable. If applying indoors, please turn off fuel sources such as heaters, furnaces and water heater pilot lights. Provide ventilation so that vapours do not accumulate and wear appropriate PPE (Personal Protection Equipment) such as, but not limited to: respirators, gloves and safety goggles.\u003c\/p\u003e\n\u003cp\u003eCLEAN AND DRY: All surfaces must be clean and free of all contaminants such as dust, dirt, oils, paint, glue, rust, algae, mildew, non-acrylic coatings and any other foreign matter that may be a bond breaker.\u003c\/p\u003e\n\u003cp\u003eThis should include and flaking or loose sealers from previous applications. Use of a light acid cleaner can be used for this purpose. Allow 24 hours for the substrate to dry before sealing.\u003c\/p\u003e\n\u003cp\u003eSURFACE CONDITION: All concrete substrates should be sound with no hollow spots, scaling or flaking.  All delaminated material should be completely removed. Shot blasting, grinding and\/or scarifying should be done in those areas.\u003c\/p\u003e\n\u003cp\u003eSUBSTRATE PROFILING: The Concrete substrate should be profiled according to the CSP (Concrete Surface Profile) standards of between 1 and 2.  This can be attained through mechanical means such as grinding, sand blasting or light scarifying or chemically through the use of a light cleaning acid and pressure washing.\u003c\/p\u003e\n\u003cp\u003eRECOATING:  If this sealer is being used to recoat concrete, it should only be used if the previous coating was a solvent based acrylic formula.  This product should never be applied over water based acrylics. \u003c\/p\u003e\n\u003cp\u003eIf the previous product is unknown, a xylene test (see below) may be used to determine the type. A small test area should be used to determine compatibility of solvents. If solvents are not compatible, blistering, peeling or delamination may occur.\u003c\/p\u003e\n\u003cp\u003eXYLENE TESTING (If needed): For this test, you will need Xylene, paper towel and plastic. Put a small amount of xylene on the paper towel and place that on the concrete. Cover the paper towel with plastic and allow to sit for 15 minutes. After 15 minutes, a solvent based acrylic will feel slippery. A water based acrylic will be a slimy mess that can be scraped off easily.\u003c\/p\u003e\n\u003cp\u003eMASKING: All areas that are not intended to receive AC the art of concrete 30% Penetrating Sealer, should be protected by masking. Protect vegetation and landscaping.\u003c\/p\u003e\n\u003cp\u003eTOUCH-UP: Finish all touch-up work prior to sealing. This includes cleaning, detailing and colouring.\u003c\/p\u003e\n\u003cp\u003ePLANNING: The substrate must be dry for all steps, 24 hours before, during and 24 hours after application. Application of AC the art of concrete 30% Penetrating Sealer should be avoided on extremely cold or hot days (if the temperature will not be within the aforementioned ranges for 12-24 hours after application). Do not apply if rain, snow or hail is being forecast for the 24 hour period after application.\u003c\/p\u003e\n\u003cp\u003eBoth the concrete and the ambient air temperature should be between 10°C and 32°C during application.\u003c\/p\u003e\n\u003cp\u003eMIXING: This product does not need any mixing.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eAPPLICATION:\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eROLLING:\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eUse a bucket grid or metal paint tray to ensure application of a thin film. (No puddling of product)\u003c\/li\u003e\n\u003cli\u003eRoller sleeves will require a solvent resistant core.\u003c\/li\u003e\n\u003cli\u003eThickness of roller sleeve will depend on the substrate being covered. A rougher surface will require a longer nap. A smooth cementitious surface such as a garage floor will require a 6 mil roller sleeve. Broom finished concrete, light exposed aggregate or a shallow stamped concrete will require a 10 mill roller sleeve. Deep exposed aggregate or a deep stamped concrete will require a 19 mil roller sleeve.\u003c\/li\u003e\n\u003cli\u003eBack rolling will help to eliminate roller lines. Back rolling should be done perpendicular to application.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003eSPRAYING:\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eThe airless sprayer used should be capable of spraying 1.0 gallons per minute (GPM) with a 65° fan tip size of between .015 to .019”. Maintain a wet edge between passes.\u003c\/li\u003e\n\u003cli\u003eA pump-up sprayer may also be used. The sprayer MUST be a solvent resistant sprayer. A sprayer tip of 1.0 gallons per minute should be sufficient to apply this product. Back-rolling may be used.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003eA single coat is usually sufficient for most applications. However, if your substrate looks “blotchy or uneven” after the first coat, a second coat may be applied.  Wait for the first coat to dry sufficiently so that you may walk on it. If a second coat is required, it can be applied exactly as the first coat.\u003c\/p\u003e\n\u003cp\u003ePlease allow the proper amount of cure time after applying sealer. For foot traffic allow 24 hours. For vehicular traffic allow 72 hours.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCLEAN UP:\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eBefore AC the art of concrete 30% Penetrating Sealer dries, solvents such as Xylene or Acetone may be used.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eSTORAGE AND CAUTIONS:\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 30% Penetrating Sealer is flammable. Avoid heat sources, spark, electric tools and open flame sources. Store in a cool dry area out of direct sunlight. Shelf life under normal recommended conditions is 2 years. Store in sealed containers. Keep area well ventilated. \u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eINHALATION: \u003c\/b\u003eUse approved NIOSH PPE (Respirator for organic vapours). \u003cb\u003eSKIN \u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCONTACT: \u003c\/b\u003eMay cause irritation.  Remove all contaminated clothing and wash before reusing. Wash affected skin area with soap and water. If symptoms persist, seek medical attention. \u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eEYE CONTACT: \u003c\/b\u003eWear eye protecting while handling product. If contact with eyes does occur, remove contact lenses (if present). Flush eyes with water or eye wash solution for 15 minutes. Seek medical Attention.  Consult the SDS sheets for further information before use of product.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eKEEP OUT OF REACH OF CHILDREN.\u003c\/b\u003e\u003c\/p\u003e\n\u003cp class=\"MsoNormal\"\u003eThis Product is classified as a Hazardous Materials and needs to be shipped according to the Transportation of Dangerous Goods (TDG) shipping regulations. Because of this, extra shipping charges will be assessed due to the TDG services needed.  This product will have to be shipped on an LTL carrier that has the capabilities to carry out this service.  You will be contacted with the extra charges needed. \u003c\/p\u003e\n\u003cp\u003e DATA SHEET DOWNLOADS\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0681\/0737\/0788\/files\/AC_30_Sealer_TDS.pub?v=1685634061\" target=\"_blank\"\u003e\u003cspan\u003eAC the art of concrete 30% Penetrating Acrylic Sealer TDS\u003c\/span\u003e\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0681\/0737\/0788\/files\/AC_30_Sealer_SDS.docx?v=1685634061\" target=\"_blank\"\u003e\u003cspan\u003eAC the art of concrete 30% Penetrating Acrylic Sealer SDS\u003c\/span\u003e\u003c\/a\u003e\u003c\/p\u003e","brand":"AC the art of concrete","offers":[{"title":"Default Title","offer_id":45380381311268,"sku":"**209122","price":372.79,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0681\/0737\/0788\/files\/ACSilane305Gallon_4b4671be-8d65-42f5-b4b9-57851798b6e6.jpg?v=1745523182"},{"product_id":"ac-the-art-of-concrete-20-penetrating-acrylic-sealer-1-gallon","title":"AC the art of concrete 20 Percent Silane 1 Gallon","description":"\u003cp\u003e\u003cb\u003ePRODUCT DESCRIPTION AND USES\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAC the art of concrete 20% Silane Penetrating Acrylic Sealer\u003c\/strong\u003e is a VOC Compliant, premium high quality, durable, abrasion resistant, single component silane Based, 20% acrylic solids sealer. This sealer is designed for use on any cementitious surface for protection and highlighting colour.\u003c\/p\u003e\n\u003cp\u003eIt is vapour permeable and will apply out of doors readily. This sealer is formulated for Canada’s extreme freeze\/thaw cycles.  Because of this sealer’s superior silane formulation, it will penetrate deeply into the concrete’s surface, therefore intensifying the bond with the concrete and slowing moisture migration and efflorescence.\u003c\/p\u003e\n\u003cp\u003eThe high quality solvents will give the user ample working time when applying AC the art of concrete 20% Penetrating Sealer. A single coat will provide protection for the concrete while providing UV protection, enhancing the beauty and colour of the concrete.\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete sealers can be used on any concrete surface including driveways, patios, walkways, stairs, garages, pool decks and even stucco.  This sealer will provide a semi-gloss finish to your concrete surface.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003ePACKAGING\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 20% Penetrating Sealer is available in 3.78L and 18.9L containers and is a ready to use formulation.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCOVERAGE\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 20% Penetrating Sealer will cover 150 - 185 square feet per gallon. (700-900 square feet per 5 gallon pail) depending on the surface finish and porosity of the substrate.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003ePLANNING AND SURFACE PREP\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 20% Penetrating Sealer must be applied to dry, clean concrete. The concrete should be fully cured (28 days or older). The concrete and ambient air temperature should be above 10°C and below 32°C.  \u003c\/p\u003e\n\u003cp\u003eThis product is flammable. If applying indoors, please turn off fuel sources such as heaters, furnaces and water heater pilot lights. Provide ventilation so that vapours do not accumulate and wear appropriate PPE (Personal Protection Equipment) such as, but not limited to: respirators, gloves and safety goggles.\u003c\/p\u003e\n\u003cp\u003eCLEAN AND DRY: All surfaces must be clean and free of all contaminants such as dust, dirt, oils, paint, glue, rust, algae, mildew, non-acrylic coatings and any other foreign matter that may be a bond breaker.\u003c\/p\u003e\n\u003cp\u003eThis should include and flaking or loose sealers from previous applications. Use of a light acid cleaner can be used for this purpose. Allow 24 hours for the substrate to dry before sealing.\u003c\/p\u003e\n\u003cp\u003eSURFACE CONDITION: All concrete substrates should be sound with no hollow spots, scaling or flaking.  All delaminated material should be completely removed. Shot blasting, grinding and\/or scarifying should be done in those areas.\u003c\/p\u003e\n\u003cp\u003eSUBSTRATE PROFILING: The Concrete substrate should be profiled according to the CSP (Concrete Surface Profile) standards of between 1 and 2.  This can be attained through mechanical means such as grinding, sand blasting or light scarifying or chemically through the use of a light cleaning acid and pressure washing.\u003c\/p\u003e\n\u003cp\u003eRECOATING:  If this sealer is being used to recoat concrete, it should only be used if the previous coating was a solvent based acrylic formula.  This product should never be applied over water based acrylics. \u003c\/p\u003e\n\u003cp\u003eIf the previous product is unknown, a xylene test (see below) may be used to determine the type. A small test area should be used to determine compatibility of solvents. If solvents are not compatible, blistering, peeling or delamination may occur.\u003c\/p\u003e\n\u003cp\u003eXYLENE TESTING (If needed): For this test, you will need Xylene, paper towel and plastic. Put a small amount of xylene on the paper towel and place that on the concrete. Cover the paper towel with plastic and allow to sit for 15 minutes. After 15 minutes, a solvent based acrylic will feel slippery. A water based acrylic will be a slimy mess that can be scraped off easily.\u003c\/p\u003e\n\u003cp\u003eMASKING: All areas that are not intended to receive AC the art of concrete 20% Penetrating Sealer, should be protected by masking. Protect vegetation and landscaping.\u003c\/p\u003e\n\u003cp\u003eTOUCH-UP: Finish all touch-up work prior to sealing. This includes cleaning, detailing and colouring.\u003c\/p\u003e\n\u003cp\u003ePLANNING: The substrate must be dry for all steps, 24 hours before, during and 24 hours after application. Application of AC the art of concrete 20% Penetrating Sealer should be avoided on extremely cold or hot days (if the temperature will not be within the aforementioned ranges for 12-24 hours after application).\u003c\/p\u003e\n\u003cp\u003eDo not apply if rain, snow or hail is being forecast for the 24 hour period after application.\u003c\/p\u003e\n\u003cp\u003eBoth the concrete and the ambient air temperature should be between 10°C and 32°C during application.\u003c\/p\u003e\n\u003cp\u003eMIXING: This product should be mixed for three minutes with a jiffy style mixer on medium speed making sure not to add air during the mixing process.  This is to make sure the matting agent is thoroughly dispersed.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eAPPLICATION:\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eROLLING:\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eUse a bucket grid or metal paint tray to ensure application of a thin film. (No puddling of product)\u003c\/li\u003e\n\u003cli\u003eRoller sleeves will require a solvent resistant core.\u003c\/li\u003e\n\u003cli\u003eThickness of roller sleeve will depend on the substrate being covered. A rougher surface will require a longer nap. A smooth cementitious surface such as a garage floor will require a 6 mil roller sleeve. Broom finished concrete, light exposed aggregate or a shallow stamped concrete will require a 10 mill roller sleeve. Deep exposed aggregate or a deep stamped concrete will require a 19 mil roller sleeve.\u003c\/li\u003e\n\u003cli\u003eBack rolling will help to eliminate roller lines. Back rolling should be done perpendicular to application.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003eSPRAYING:\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eThe airless sprayer used should be capable of spraying 0.5 gallons per minute (GPM) with a 65° fan tip size of between .015 to .019”. Maintain a wet edge between passes.\u003c\/li\u003e\n\u003cli\u003eA pump-up sprayer may also be used. The sprayer MUST be a solvent resistant sprayer. A sprayer tip of .5 gallons per minute should be sufficient to apply this product. Back-rolling may be used.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003eA single coat is usually sufficient for most applications. However, if your substrate looks “blotchy or uneven” after the first coat, a second coat may be applied.  Wait for the first coat to dry sufficiently so that you may walk on it. If a second coat is required, it can be applied exactly as the first coat.\u003c\/p\u003e\n\u003cp\u003ePlease allow the proper amount of cure time after applying sealer. For foot traffic allow 24 hours. For vehicular traffic allow 72 hours.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCLEAN UP:\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eBefore AC the art of concrete 20% Penetrating Sealer dries, solvents such as Xylene or Acetone may be used.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eSTORAGE AND CAUTIONS:\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 20% Penetrating Sealer is flammable. Avoid heat sources, spark, electric tools and open flame sources. Store in a cool dry area out of direct sunlight. Shelf life under normal recommended conditions is 2 years. Store in sealed containers. Keep area well ventilated.  \u003cb\u003eINHALATION: \u003c\/b\u003eUse approved NIOSH PPE (Respirator for organic vapours). \u003cb\u003eSKIN CONTACT: \u003c\/b\u003eMay cause irritation. \u003c\/p\u003e\n\u003cp\u003eRemove all contaminated clothing and wash before reusing. Wash affected skin area with soap and water. If symptoms persist, seek medical attention.  \u003cb\u003eEYE CONTACT: \u003c\/b\u003eWear eye protecting while handling product. If contact with eyes does occur, remove contact lenses (if present). Flush eyes with water or eye wash solution for 15 minutes. Seek medical Attention.  Consult the SDS sheets for further information before use of product. \u003cb\u003eKEEP OUT OF REACH OF CHILDREN.\u003c\/b\u003e\u003c\/p\u003e\n\u003cp class=\"MsoNormal\"\u003eThis Product is classified as a Hazardous Materials and needs to be shipped according to the Transportation of Dangerous Goods (TDG) shipping regulations. Because of this, extra shipping charges will be assessed due to the TDG services needed.  This product will have to be shipped on an LTL carrier that has the capabilities to carry out this service.  You will be contacted with the extra charges needed. \u003c\/p\u003e\n\u003cp\u003eDATA SHEET DOWNLOADS\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0681\/0737\/0788\/files\/AC_20_Silane_Sealer_400GPL_TDS.pdf?v=1744752662\" rel=\"noopener\" target=\"_blank\"\u003e\u003cspan\u003eAC the art of concrete 20% Penetrating Acrylic Sealer TDS\u003c\/span\u003e\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca rel=\"noopener\" href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0681\/0737\/0788\/files\/AC_20_Silane_Sealer_400GPL_SDS.pdf?v=1744752662\" target=\"_blank\"\u003e\u003cspan\u003eAC the art of concrete 20% Penetrating Acrylic Sealer SDS\u003c\/span\u003e\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e","brand":"AC the art of concrete","offers":[{"title":"Default Title","offer_id":47206602047780,"sku":"**210289","price":85.29,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0681\/0737\/0788\/files\/AC_Silane_20_1_Gallon.png?v=1745524204"},{"product_id":"ac-the-art-of-concrete-30-penetrating-acrylic-sealer-1-gallon","title":"AC the art of concrete 30 Percent Silane 1 Gallon","description":"\u003cp\u003e\u003cb\u003ePRODUCT DESCRIPTION AND USES\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAC the art of concrete 30% Silane Penetrating Acrylic Sealer\u003c\/strong\u003e is a VOC Compliant, premium high quality, durable, abrasion resistant, single component silane Based, 30% acrylic solids sealer. This sealer is designed for use on any cementitious surface for protection and highlighting colour.\u003c\/p\u003e\n\u003cp\u003eIt is vapour permeable and will apply out of doors readily. This sealer is formulated for Canada’s extreme freeze\/thaw cycles.  Because of this sealer’s superior silane formulation, it will penetrate deeply into the concrete’s surface, therefore intensifying the bond with the concrete and slowing moisture migration and efflorescence.\u003c\/p\u003e\n\u003cp\u003eThe high quality solvents will give the user ample working time when applying AC the art of concrete 30% Penetrating Sealer. A single coat will provide protection for the concrete while providing UV protection, enhancing the beauty and colour of the concrete.\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete sealers can be used on any concrete surface including driveways, patios, walkways, stairs, garages, pool decks and even stucco.  This sealer will provide a semi-gloss finish to your concrete surface.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003ePACKAGING\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 30% Penetrating Sealer is available in 3.78L and 18.9L containers and is a ready to use formulation.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCOVERAGE\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 30% Penetrating Sealer will cover 150 - 185 square feet per gallon. (700-900 square feet per 5 gallon pail) depending on the surface finish and porosity of the substrate.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003ePLANNING AND SURFACE PREP\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 30% Penetrating Sealer must be applied to dry, clean concrete. The concrete should be fully cured (28 days or older). The concrete and ambient air temperature should be above 10°C and below 32°C.  \u003c\/p\u003e\n\u003cp\u003eThis product is flammable. If applying indoors, please turn off fuel sources such as heaters, furnaces and water heater pilot lights. Provide ventilation so that vapours do not accumulate and wear appropriate PPE (Personal Protection Equipment) such as, but not limited to: respirators, gloves and safety goggles.\u003c\/p\u003e\n\u003cp\u003eCLEAN AND DRY: All surfaces must be clean and free of all contaminants such as dust, dirt, oils, paint, glue, rust, algae, mildew, non-acrylic coatings and any other foreign matter that may be a bond breaker.\u003c\/p\u003e\n\u003cp\u003eThis should include and flaking or loose sealers from previous applications. Use of a light acid cleaner can be used for this purpose. Allow 24 hours for the substrate to dry before sealing.\u003c\/p\u003e\n\u003cp\u003eSURFACE CONDITION: All concrete substrates should be sound with no hollow spots, scaling or flaking.  All delaminated material should be completely removed. Shot blasting, grinding and\/or scarifying should be done in those areas.\u003c\/p\u003e\n\u003cp\u003eSUBSTRATE PROFILING: The Concrete substrate should be profiled according to the CSP (Concrete Surface Profile) standards of between 1 and 2.  This can be attained through mechanical means such as grinding, sand blasting or light scarifying or chemically through the use of a light cleaning acid and pressure washing.\u003c\/p\u003e\n\u003cp\u003eRECOATING:  If this sealer is being used to recoat concrete, it should only be used if the previous coating was a solvent based acrylic formula.  This product should never be applied over water based acrylics. \u003c\/p\u003e\n\u003cp\u003eIf the previous product is unknown, a xylene test (see below) may be used to determine the type. A small test area should be used to determine compatibility of solvents. If solvents are not compatible, blistering, peeling or delamination may occur.\u003c\/p\u003e\n\u003cp\u003eXYLENE TESTING (If needed): For this test, you will need Xylene, paper towel and plastic. Put a small amount of xylene on the paper towel and place that on the concrete. Cover the paper towel with plastic and allow to sit for 15 minutes. After 15 minutes, a solvent based acrylic will feel slippery. A water based acrylic will be a slimy mess that can be scraped off easily.\u003c\/p\u003e\n\u003cp\u003eMASKING: All areas that are not intended to receive AC the art of concrete 30% Penetrating Sealer, should be protected by masking. Protect vegetation and landscaping.\u003c\/p\u003e\n\u003cp\u003eTOUCH-UP: Finish all touch-up work prior to sealing. This includes cleaning, detailing and colouring.\u003c\/p\u003e\n\u003cp\u003ePLANNING: The substrate must be dry for all steps, 24 hours before, during and 24 hours after application. Application of AC the art of concrete 30% Penetrating Sealer should be avoided on extremely cold or hot days (if the temperature will not be within the aforementioned ranges for 12-24 hours after application). Do not apply if rain, snow or hail is being forecast for the 24 hour period after application.\u003c\/p\u003e\n\u003cp\u003eBoth the concrete and the ambient air temperature should be between 10°C and 32°C during application.\u003c\/p\u003e\n\u003cp\u003eMIXING: This product does not need any mixing.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eAPPLICATION:\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eROLLING:\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eUse a bucket grid or metal paint tray to ensure application of a thin film. (No puddling of product)\u003c\/li\u003e\n\u003cli\u003eRoller sleeves will require a solvent resistant core.\u003c\/li\u003e\n\u003cli\u003eThickness of roller sleeve will depend on the substrate being covered. A rougher surface will require a longer nap. A smooth cementitious surface such as a garage floor will require a 6 mil roller sleeve. Broom finished concrete, light exposed aggregate or a shallow stamped concrete will require a 10 mill roller sleeve. Deep exposed aggregate or a deep stamped concrete will require a 19 mil roller sleeve.\u003c\/li\u003e\n\u003cli\u003eBack rolling will help to eliminate roller lines. Back rolling should be done perpendicular to application.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003eSPRAYING:\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eThe airless sprayer used should be capable of spraying 1.0 gallons per minute (GPM) with a 65° fan tip size of between .015 to .019”. Maintain a wet edge between passes.\u003c\/li\u003e\n\u003cli\u003eA pump-up sprayer may also be used. The sprayer MUST be a solvent resistant sprayer. A sprayer tip of 1.0 gallons per minute should be sufficient to apply this product. Back-rolling may be used.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003eA single coat is usually sufficient for most applications. However, if your substrate looks “blotchy or uneven” after the first coat, a second coat may be applied.  Wait for the first coat to dry sufficiently so that you may walk on it. If a second coat is required, it can be applied exactly as the first coat.\u003c\/p\u003e\n\u003cp\u003ePlease allow the proper amount of cure time after applying sealer. For foot traffic allow 24 hours. For vehicular traffic allow 72 hours.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCLEAN UP:\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eBefore AC the art of concrete 30% Penetrating Sealer dries, solvents such as Xylene or Acetone may be used.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eSTORAGE AND CAUTIONS:\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 30% Penetrating Sealer is flammable. Avoid heat sources, spark, electric tools and open flame sources. Store in a cool dry area out of direct sunlight. Shelf life under normal recommended conditions is 2 years. Store in sealed containers. Keep area well ventilated. \u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eINHALATION: \u003c\/b\u003eUse approved NIOSH PPE (Respirator for organic vapours). \u003cb\u003eSKIN \u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCONTACT: \u003c\/b\u003eMay cause irritation.  Remove all contaminated clothing and wash before reusing. Wash affected skin area with soap and water. If symptoms persist, seek medical attention. \u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eEYE CONTACT: \u003c\/b\u003eWear eye protecting while handling product. If contact with eyes does occur, remove contact lenses (if present). Flush eyes with water or eye wash solution for 15 minutes. Seek medical Attention.  Consult the SDS sheets for further information before use of product.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eKEEP OUT OF REACH OF CHILDREN.\u003c\/b\u003e\u003c\/p\u003e\n\u003cp class=\"MsoNormal\"\u003eThis Product is classified as a Hazardous Materials and needs to be shipped according to the Transportation of Dangerous Goods (TDG) shipping regulations. Because of this, extra shipping charges will be assessed due to the TDG services needed.  This product will have to be shipped on an LTL carrier that has the capabilities to carry out this service.  You will be contacted with the extra charges needed. \u003c\/p\u003e\n\u003cp\u003e DATA SHEET DOWNLOADS\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0681\/0737\/0788\/files\/AC_30_Sealer_TDS.pub?v=1685634061\" target=\"_blank\"\u003e\u003cspan\u003eAC the art of concrete 30% Penetrating Acrylic Sealer TDS\u003c\/span\u003e\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0681\/0737\/0788\/files\/AC_30_Sealer_SDS.docx?v=1685634061\" target=\"_blank\"\u003e\u003cspan\u003eAC the art of concrete 30% Penetrating Acrylic Sealer SDS\u003c\/span\u003e\u003c\/a\u003e\u003c\/p\u003e","brand":"AC the art of concrete","offers":[{"title":"Default Title","offer_id":47206672728356,"sku":"**210296","price":93.79,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0681\/0737\/0788\/files\/AC_Silane_30_1_Gallon.png?v=1745524325"},{"product_id":"ac-the-art-of-concrete-25-contractor-grade-5-gallon","title":"AC - the art of concrete 25 Percent  Sealer 5 Gallon","description":"\u003cp\u003e\u003cb\u003ePRODUCT DESCRIPTION AND USES\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 25% Sealer is a VOC Compliant, premium high quality, durable, abrasion resistant, single component 25% acrylic solids sealer for new or existing concrete and masonry. The 25% solids content provides a UV stable high-gloss finish that will colour enhance the concrete surface. AC the art of concrete 25% Sealer  is ideal for use on concrete that is at least 28 days old. This product may be used on all concrete no matter the finish. Concrete may be smooth or rough finished and may include:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eConcrete Flatwork\u003c\/li\u003e\n\u003cli\u003eLight Commercial\u003c\/li\u003e\n\u003cli\u003eArchitectural Concrete\u003c\/li\u003e\n\u003cli\u003eBrick\u003c\/li\u003e\n\u003cli\u003eStone\u003c\/li\u003e\n\u003cli\u003ePrecast concrete \u0026amp; walls\u003c\/li\u003e\n\u003cli\u003eResidential walkways, driveways and patios\u003c\/li\u003e\n\u003cli\u003eConcrete curbing and borders\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003ePACKAGING\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 25% Sealer is available in 18.9L containers and is a ready to use formulation.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCOVERAGE\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 25% Sealer will cover 150 - 200 square feet per gallon. (700-1000 square feet per 5 gallon pail) depending on the surface finish and porosity of the substrate.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003ePLANNING AND SURFACE PREP\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 25% Sealer can be applied to concrete that is at least 28 days old. Finish trowel the concrete and allow surface water to dissipate completely. Use a low pressure sprayer (20 - 30 lbs.) and apply a uniform coat at a rate of coverage as specified below. Avoid heavy accumulations. A second coat may be necessary where concrete is very porous and where absorption is very rapid. An additional coat may be applied after first coat is tack free.\u003c\/p\u003e\n\u003cp\u003eBroomed Concrete - 250-350 square feet per gallon.\u003c\/p\u003e\n\u003cp\u003eTroweled Concrete - 300-450 square feet per gallon.\u003c\/p\u003e\n\u003cp\u003eDustproof Seal - 250-400 square feet per gallon.\u003c\/p\u003e\n\u003cp\u003eSecond Coat - 300-600 square feet per gallon.\u003c\/p\u003e\n\u003cp\u003e\u003ci\u003e(These coverage rates are approximations only. Many factors will affect coverage rates.  These will include, but are not limited to: surface texture, porosity of the concrete, and weather conditions.)\u003c\/i\u003e\u003c\/p\u003e\n\u003cp\u003eCLEAN AND DRY: AC the art of concrete 25% Sealer may be applied on fully cured concrete. All surfaces must be clean and free of all contaminants such as dust, dirt, oils, efflorescence, grease, paint, glue, rust, algae, mildew, non-acrylic coatings and any other foreign matter that may be a bond breaker. Allow 24 hours for the substrate to dry before applying.\u003c\/p\u003e\n\u003cp\u003eSURFACE CONDITION: All concrete substrates should be sound with no hollow spots, scaling or flaking.  All delaminated material should be completely removed. Shot blasting, grinding and\/or scarifying should be done in those areas.\u003c\/p\u003e\n\u003cp\u003eMASKING: All areas that are not intended to receive AC the art of concrete 25% Sealer, should be protected by masking. Protect vegetation and landscaping.\u003c\/p\u003e\n\u003cp\u003eTOUCH-UP: Finish all touch-up work prior to sealing. This includes cleaning, detailing and colouring.\u003c\/p\u003e\n\u003cp\u003ePLANNING: The substrate must be dry for all steps, during and 24 hours after application. Application of AC the art of concrete 25% Sealer should be avoided on extremely cold or hot days (if the temperature will not be within the aforementioned ranges for 12-24 hours after application). Do not apply if rain, snow or hail is being forecast for the 24 hour period after application.\u003c\/p\u003e\n\u003cp\u003eBoth the concrete and the ambient air temperature should be between 10°C and 32°C during application.\u003c\/p\u003e\n\u003cp\u003eMIXING: This product does not need mixing. It is ready for use and no dilution is necessary.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eAPPLICATION: \u003c\/b\u003eAC the art of concrete 25% Sealer will darken concrete.\u003c\/p\u003e\n\u003cp\u003eROLLING:\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eUse a bucket grid or metal paint tray to ensure application of a thin film. (No puddling of product)\u003c\/li\u003e\n\u003cli\u003eRoller sleeves will require a solvent resistant core.\u003c\/li\u003e\n\u003cli\u003eThickness of roller sleeve will depend on the substrate being covered. A rougher surface will require a longer nap. A smooth cementitious surface such as a garage floor will require a 6 mil roller sleeve. Broom finished concrete, light exposed aggregate or a shallow stamped concrete will require a 10 mill roller sleeve. Deep exposed aggregate or a deep stamped concrete will require a 19 mil roller sleeve.\u003c\/li\u003e\n\u003cli\u003eBack rolling will help to eliminate roller lines. Back rolling should be done perpendicular to application.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eSPRAYING:\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eUse a low pressure sprayer (20 - 30 lbs.) and apply a uniform coat at a rate of coverage as specified below. Avoid heavy accumulations. A second coat may be necessary where concrete is very porous and where absorption is very rapid. An additional coat may be applied after first coat is tack free.\u003c\/li\u003e\n\u003cli\u003eA single coat is usually sufficient for most applications. However, if your substrate looks “blotchy or uneven” after the first coat, a second coat may be applied. Wait for the first coat to dry sufficiently so that you may walk on it. If a second coat is required, it can be applied exactly as the first coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003ePlease allow the proper amount of cure time after applying sealer. For foot traffic allow 24 hours. For vehicular traffic allow 72 hours.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCLEAN UP:\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eBefore AC the art of concrete 25% Sealer dries, solvents such as Xylene or Acetone may be used.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eSTORAGE AND CAUTIONS:\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 25% Sealer is flammable. Avoid heat sources, spark, electric tools and open flame sources. Store in a cool dry area out of direct sunlight. Shelf life under normal recommended conditions is 2 years. Store in sealed containers. Keep area well ventilated. Do not allow to freeze. \u003cb\u003eINHALATION: \u003c\/b\u003eUse approved NIOSH PPE (Respirator for organic vapours). \u003cb\u003eSKIN CONTACT: \u003c\/b\u003eMay cause irritation.  Remove all contaminated clothing and wash before reusing. Wash affected skin area with soap and water. If symptoms persist, seek medical attention.  \u003cb\u003eEYE CONTACT: \u003c\/b\u003eWear eye protecting while handling product. If contact with eyes does occur, remove contact lenses (if present). Flush eyes with water or eye wash solution for 15 minutes. Seek medical Attention.  Consult the SDS sheets for further information before use of product. \u003cb\u003eKEEP OUT OF REACH OF CHILDREN.\u003c\/b\u003e\u003c\/p\u003e\n\u003cp class=\"MsoNormal\"\u003eThis Product is classified as a Hazardous Materials and needs to be shipped according to the Transportation of Dangerous Goods (TDG) shipping regulations. Because of this, extra shipping charges will be assessed due to the TDG services needed.  This product will have to be shipped on an LTL carrier that has the capabilities to carry out this service.  You will be contacted with the extra charges needed. \u003c\/p\u003e\n\u003cp\u003e DATA SHEET DOWNLOADS\u003c\/p\u003e\n\u003cp\u003e\u003ca rel=\"noopener\" href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0681\/0737\/0788\/files\/AC_25_Contractor_Grade_Sealer_400GPL_TDS.pub?v=1744898597\" target=\"_blank\"\u003eAC - the art of concrete 25% Sealer TDS\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca rel=\"noopener\" href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0681\/0737\/0788\/files\/AC_25_Contractor_Grade_Sealer_400GPL_SDS.docx?v=1744898597\" target=\"_blank\"\u003eAC - the art of concrete 25% Cure \u0026amp; Seal SDS\u003c\/a\u003e\u003c\/p\u003e","brand":"AC the art of concrete","offers":[{"title":"Default Title","offer_id":48133975114020,"sku":"**220914","price":234.79,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0681\/0737\/0788\/files\/ACContractor255Gallon.jpg?v=1745523182"},{"product_id":"ac-the-art-of-concrete-30-contractor-grade-5-gallon","title":"AC - the art of concrete 30 Percent Sealer 5 Gallon","description":"\u003cp\u003e\u003cb\u003ePRODUCT DESCRIPTION AND USES\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 30% Sealer is a VOC Compliant, premium high quality, durable, abrasion resistant, single component 30% acrylic solids sealer for new or existing concrete and masonry. The 30% solids content provides a UV stable high-gloss finish that will colour enhance the concrete surface. AC the art of concrete 30% Sealer  is ideal for use on concrete that is at least 28 days old. This product may be used on all concrete no matter the finish. Concrete may be smooth or rough finished and may include:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eConcrete Flatwork\u003c\/li\u003e\n\u003cli\u003eLight Commercial\u003c\/li\u003e\n\u003cli\u003eArchitectural Concrete\u003c\/li\u003e\n\u003cli\u003eBrick\u003c\/li\u003e\n\u003cli\u003eStone\u003c\/li\u003e\n\u003cli\u003ePrecast concrete \u0026amp; walls\u003c\/li\u003e\n\u003cli\u003eResidential walkways, driveways and patios\u003c\/li\u003e\n\u003cli\u003eConcrete curbing and borders\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003ePACKAGING\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 30% Sealer is available in 18.9L containers and is a ready to use formulation.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCOVERAGE\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 30% Sealer will cover 150 - 200 square feet per gallon. (700-1000 square feet per 5 gallon pail) depending on the surface finish and porosity of the substrate.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003ePLANNING AND SURFACE PREP\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 30% Sealer can be applied to concrete that is at least 28 days old. Finish trowel the concrete and allow surface water to dissipate completely. Use a low pressure sprayer (20 - 30 lbs.) and apply a uniform coat at a rate of coverage as specified below. Avoid heavy accumulations. A second coat may be necessary where concrete is very porous and where absorption is very rapid. An additional coat may be applied after first coat is tack free.\u003c\/p\u003e\n\u003cp\u003eBroomed Concrete - 250-350 square feet per gallon.\u003c\/p\u003e\n\u003cp\u003eTroweled Concrete - 300-450 square feet per gallon.\u003c\/p\u003e\n\u003cp\u003eDustproof Seal - 250-400 square feet per gallon.\u003c\/p\u003e\n\u003cp\u003eSecond Coat - 300-600 square feet per gallon.\u003c\/p\u003e\n\u003cp\u003e\u003ci\u003e(These coverage rates are approximations only. Many factors will affect coverage rates.  These will include, but are not limited to: surface texture, porosity of the concrete, and weather conditions.)\u003c\/i\u003e\u003c\/p\u003e\n\u003cp\u003eCLEAN AND DRY: AC the art of concrete 30% Sealer may be applied on fully cured concrete. All surfaces must be clean and free of all contaminants such as dust, dirt, oils, efflorescence, grease, paint, glue, rust, algae, mildew, non-acrylic coatings and any other foreign matter that may be a bond breaker. Allow 24 hours for the substrate to dry before applying.\u003c\/p\u003e\n\u003cp\u003eSURFACE CONDITION: All concrete substrates should be sound with no hollow spots, scaling or flaking.  All delaminated material should be completely removed. Shot blasting, grinding and\/or scarifying should be done in those areas.\u003c\/p\u003e\n\u003cp\u003eMASKING: All areas that are not intended to receive AC the art of concrete 30% Sealer, should be protected by masking. Protect vegetation and landscaping.\u003c\/p\u003e\n\u003cp\u003eTOUCH-UP: Finish all touch-up work prior to sealing. This includes cleaning, detailing and colouring.\u003c\/p\u003e\n\u003cp\u003ePLANNING: The substrate must be dry for all steps, during and 24 hours after application. Application of AC the art of concrete 30% Sealer should be avoided on extremely cold or hot days (if the temperature will not be within the aforementioned ranges for 12-24 hours after application). Do not apply if rain, snow or hail is being forecast for the 24 hour period after application.\u003c\/p\u003e\n\u003cp\u003eBoth the concrete and the ambient air temperature should be between 10°C and 32°C during application.\u003c\/p\u003e\n\u003cp\u003eMIXING: This product does not need mixing. It is ready for use and no dilution is necessary.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eAPPLICATION: \u003c\/b\u003eAC the art of concrete 30% Sealer will darken concrete.\u003c\/p\u003e\n\u003cp\u003eROLLING:\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eUse a bucket grid or metal paint tray to ensure application of a thin film. (No puddling of product)\u003c\/li\u003e\n\u003cli\u003eRoller sleeves will require a solvent resistant core.\u003c\/li\u003e\n\u003cli\u003eThickness of roller sleeve will depend on the substrate being covered. A rougher surface will require a longer nap. A smooth cementitious surface such as a garage floor will require a 6 mil roller sleeve. Broom finished concrete, light exposed aggregate or a shallow stamped concrete will require a 10 mill roller sleeve. Deep exposed aggregate or a deep stamped concrete will require a 19 mil roller sleeve.\u003c\/li\u003e\n\u003cli\u003eBack rolling will help to eliminate roller lines. Back rolling should be done perpendicular to application.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eSPRAYING:\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eUse a low pressure sprayer (20 - 30 lbs.) and apply a uniform coat at a rate of coverage as specified below. Avoid heavy accumulations. A second coat may be necessary where concrete is very porous and where absorption is very rapid. An additional coat may be applied after first coat is tack free.\u003c\/li\u003e\n\u003cli\u003eA single coat is usually sufficient for most applications. However, if your substrate looks “blotchy or uneven” after the first coat, a second coat may be applied. Wait for the first coat to dry sufficiently so that you may walk on it. If a second coat is required, it can be applied exactly as the first coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003ePlease allow the proper amount of cure time after applying sealer. For foot traffic allow 24 hours. For vehicular traffic allow 72 hours.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCLEAN UP:\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eBefore AC the art of concrete 30% Sealer dries, solvents such as Xylene or Acetone may be used.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eSTORAGE AND CAUTIONS:\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 30% Sealer is flammable. Avoid heat sources, spark, electric tools and open flame sources. Store in a cool dry area out of direct sunlight. Shelf life under normal recommended conditions is 2 years. Store in sealed containers. Keep area well ventilated. Do not allow to freeze. \u003cb\u003eINHALATION: \u003c\/b\u003eUse approved NIOSH PPE (Respirator for organic vapours). \u003cb\u003eSKIN CONTACT: \u003c\/b\u003eMay cause irritation.  Remove all contaminated clothing and wash before reusing. Wash affected skin area with soap and water. If symptoms persist, seek medical attention.  \u003cb\u003eEYE CONTACT: \u003c\/b\u003eWear eye protecting while handling product. If contact with eyes does occur, remove contact lenses (if present). Flush eyes with water or eye wash solution for 15 minutes. Seek medical Attention.  Consult the SDS sheets for further information before use of product. \u003cb\u003eKEEP OUT OF REACH OF CHILDREN.\u003c\/b\u003e\u003c\/p\u003e\n\u003cp class=\"MsoNormal\"\u003eThis Product is classified as a Hazardous Materials and needs to be shipped according to the Transportation of Dangerous Goods (TDG) shipping regulations. Because of this, extra shipping charges will be assessed due to the TDG services needed.  This product will have to be shipped on an LTL carrier that has the capabilities to carry out this service.  You will be contacted with the extra charges needed. \u003c\/p\u003e\n\u003cp\u003e DATA SHEET DOWNLOADS\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0681\/0737\/0788\/files\/AC_30_Contractor_Grade_Sealer_400GPL_TDS.pub?v=1744898768\" rel=\"noopener\" target=\"_blank\"\u003eAC - the art of concrete 30% Sealer TDS\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0681\/0737\/0788\/files\/AC_30_Contractor_Grade_Sealer_400GPL_SDS.docx?v=1744898768\" rel=\"noopener\" target=\"_blank\"\u003eAC - the art of concrete 30% Cure \u0026amp; Seal SDS\u003c\/a\u003e\u003c\/p\u003e","brand":"AC the art of concrete","offers":[{"title":"Default Title","offer_id":48134437339428,"sku":"**209139","price":250.79,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0681\/0737\/0788\/files\/ACContractor305Gallon.jpg?v=1745523182"},{"product_id":"ac-the-art-of-concrete-20-contractor-grade-1-gallon","title":"AC - the art of concrete 20 Percent Sealer 1 Gallon","description":"\u003cp\u003e\u003cb\u003ePRODUCT DESCRIPTION AND USES\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 20% Sealer is a VOC Compliant, premium high quality, durable, abrasion resistant, single component 20% acrylic solids sealer for new or existing concrete and masonry. The 20% solids content provides a UV stable high-gloss finish that will colour enhance the concrete surface. AC the art of concrete 20% Sealer  is ideal for use on concrete that is at least 28 days old. This product may be used on all concrete no matter the finish. Concrete may be smooth or rough finished and may include:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eConcrete Flatwork\u003c\/li\u003e\n\u003cli\u003eLight Commercial\u003c\/li\u003e\n\u003cli\u003eArchitectural Concrete\u003c\/li\u003e\n\u003cli\u003eBrick\u003c\/li\u003e\n\u003cli\u003eStone\u003c\/li\u003e\n\u003cli\u003ePrecast concrete \u0026amp; walls\u003c\/li\u003e\n\u003cli\u003eResidential walkways, driveways and patios\u003c\/li\u003e\n\u003cli\u003eConcrete curbing and borders\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003ePACKAGING\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 20% Sealer is available in 18.9L containers and is a ready to use formulation.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCOVERAGE\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 20% Sealer will cover 150 - 200 square feet per gallon. (700-1000 square feet per 5 gallon pail) depending on the surface finish and porosity of the substrate.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003ePLANNING AND SURFACE PREP\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 20% Sealer can be applied to concrete that is at least 28 days old. Finish trowel the concrete and allow surface water to dissipate completely. Use a low pressure sprayer (20 - 30 lbs.) and apply a uniform coat at a rate of coverage as specified below. Avoid heavy accumulations. A second coat may be necessary where concrete is very porous and where absorption is very rapid. An additional coat may be applied after first coat is tack free.\u003c\/p\u003e\n\u003cp\u003eBroomed Concrete - 250-350 square feet per gallon.\u003c\/p\u003e\n\u003cp\u003eTroweled Concrete - 300-450 square feet per gallon.\u003c\/p\u003e\n\u003cp\u003eDustproof Seal - 250-400 square feet per gallon.\u003c\/p\u003e\n\u003cp\u003eSecond Coat - 300-600 square feet per gallon.\u003c\/p\u003e\n\u003cp\u003e\u003ci\u003e(These coverage rates are approximations only. Many factors will affect coverage rates.  These will include, but are not limited to: surface texture, porosity of the concrete, and weather conditions.)\u003c\/i\u003e\u003c\/p\u003e\n\u003cp\u003eCLEAN AND DRY: AC the art of concrete 20% Sealer may be applied on fully cured concrete. All surfaces must be clean and free of all contaminants such as dust, dirt, oils, efflorescence, grease, paint, glue, rust, algae, mildew, non-acrylic coatings and any other foreign matter that may be a bond breaker. Allow 24 hours for the substrate to dry before applying.\u003c\/p\u003e\n\u003cp\u003eSURFACE CONDITION: All concrete substrates should be sound with no hollow spots, scaling or flaking.  All delaminated material should be completely removed. Shot blasting, grinding and\/or scarifying should be done in those areas.\u003c\/p\u003e\n\u003cp\u003eMASKING: All areas that are not intended to receive AC the art of concrete 20% Sealer, should be protected by masking. Protect vegetation and landscaping.\u003c\/p\u003e\n\u003cp\u003eTOUCH-UP: Finish all touch-up work prior to sealing. This includes cleaning, detailing and colouring.\u003c\/p\u003e\n\u003cp\u003ePLANNING: The substrate must be dry for all steps, during and 24 hours after application. Application of AC the art of concrete 20% Sealer should be avoided on extremely cold or hot days (if the temperature will not be within the aforementioned ranges for 12-24 hours after application). Do not apply if rain, snow or hail is being forecast for the 24 hour period after application.\u003c\/p\u003e\n\u003cp\u003eBoth the concrete and the ambient air temperature should be between 10°C and 32°C during application.\u003c\/p\u003e\n\u003cp\u003eMIXING: This product does not need mixing. It is ready for use and no dilution is necessary.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eAPPLICATION: \u003c\/b\u003eAC the art of concrete 20% Sealer will darken concrete.\u003c\/p\u003e\n\u003cp\u003eROLLING:\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eUse a bucket grid or metal paint tray to ensure application of a thin film. (No puddling of product)\u003c\/li\u003e\n\u003cli\u003eRoller sleeves will require a solvent resistant core.\u003c\/li\u003e\n\u003cli\u003eThickness of roller sleeve will depend on the substrate being covered. A rougher surface will require a longer nap. A smooth cementitious surface such as a garage floor will require a 6 mil roller sleeve. Broom finished concrete, light exposed aggregate or a shallow stamped concrete will require a 10 mill roller sleeve. Deep exposed aggregate or a deep stamped concrete will require a 19 mil roller sleeve.\u003c\/li\u003e\n\u003cli\u003eBack rolling will help to eliminate roller lines. Back rolling should be done perpendicular to application.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eSPRAYING:\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eUse a low pressure sprayer (20 - 30 lbs.) and apply a uniform coat at a rate of coverage as specified below. Avoid heavy accumulations. A second coat may be necessary where concrete is very porous and where absorption is very rapid. An additional coat may be applied after first coat is tack free.\u003c\/li\u003e\n\u003cli\u003eA single coat is usually sufficient for most applications. However, if your substrate looks “blotchy or uneven” after the first coat, a second coat may be applied. Wait for the first coat to dry sufficiently so that you may walk on it. If a second coat is required, it can be applied exactly as the first coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003ePlease allow the proper amount of cure time after applying sealer. For foot traffic allow 24 hours. For vehicular traffic allow 72 hours.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCLEAN UP:\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eBefore AC the art of concrete 20% Sealer dries, solvents such as Xylene or Acetone may be used.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eSTORAGE AND CAUTIONS:\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 20% Sealer is flammable. Avoid heat sources, spark, electric tools and open flame sources. Store in a cool dry area out of direct sunlight. Shelf life under normal recommended conditions is 2 years. Store in sealed containers. Keep area well ventilated. Do not allow to freeze. \u003cb\u003eINHALATION: \u003c\/b\u003eUse approved NIOSH PPE (Respirator for organic vapours). \u003cb\u003eSKIN CONTACT: \u003c\/b\u003eMay cause irritation.  Remove all contaminated clothing and wash before reusing. Wash affected skin area with soap and water. If symptoms persist, seek medical attention.  \u003cb\u003eEYE CONTACT: \u003c\/b\u003eWear eye protecting while handling product. If contact with eyes does occur, remove contact lenses (if present). Flush eyes with water or eye wash solution for 15 minutes. Seek medical Attention.  Consult the SDS sheets for further information before use of product. \u003cb\u003eKEEP OUT OF REACH OF CHILDREN.\u003c\/b\u003e\u003c\/p\u003e\n\u003cp class=\"MsoNormal\"\u003eThis Product is classified as a Hazardous Materials and needs to be shipped according to the Transportation of Dangerous Goods (TDG) shipping regulations. Because of this, extra shipping charges will be assessed due to the TDG services needed.  This product will have to be shipped on an LTL carrier that has the capabilities to carry out this service.  You will be contacted with the extra charges needed. \u003c\/p\u003e\n\u003cp\u003e DATA SHEET DOWNLOADS\u003c\/p\u003e\n\u003cp\u003e\u003ca rel=\"noopener\" href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0681\/0737\/0788\/files\/AC_20_Contractor_Grade_Sealer_400GPL_TDS.pdf?v=1744754087\" target=\"_blank\"\u003eAC - the art of concrete 20% Sealer TDS\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca rel=\"noopener\" href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0681\/0737\/0788\/files\/AC_20_Contractor_Grade_400GPL_SDS.pdf?v=1744754087\" target=\"_blank\"\u003eAC - the art of concrete 20% Cure \u0026amp; Seal SDS\u003c\/a\u003e\u003c\/p\u003e","brand":"AC the art of concrete","offers":[{"title":"Default Title","offer_id":48134463553828,"sku":"**262206","price":56.79,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0681\/0737\/0788\/files\/ACContractor201Gallon.jpg?v=1716308341"},{"product_id":"ac-the-art-of-concrete-25-contractor-grade-1-gallon","title":"AC - the art of concrete 25 Percent Sealer 1 Gallon","description":"\u003cp\u003e\u003cb\u003ePRODUCT DESCRIPTION AND USES\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 25% Sealer is a VOC Compliant, premium high quality, durable, abrasion resistant, single component 25% acrylic solids sealer for new or existing concrete and masonry. The 25% solids content provides a UV stable high-gloss finish that will colour enhance the concrete surface. AC the art of concrete 25% Sealer  is ideal for use on concrete that is at least 28 days old. This product may be used on all concrete no matter the finish. Concrete may be smooth or rough finished and may include:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eConcrete Flatwork\u003c\/li\u003e\n\u003cli\u003eLight Commercial\u003c\/li\u003e\n\u003cli\u003eArchitectural Concrete\u003c\/li\u003e\n\u003cli\u003eBrick\u003c\/li\u003e\n\u003cli\u003eStone\u003c\/li\u003e\n\u003cli\u003ePrecast concrete \u0026amp; walls\u003c\/li\u003e\n\u003cli\u003eResidential walkways, driveways and patios\u003c\/li\u003e\n\u003cli\u003eConcrete curbing and borders\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003ePACKAGING\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 25% Sealer is available in 18.9L containers and is a ready to use formulation.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCOVERAGE\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 25% Sealer will cover 150 - 200 square feet per gallon. (700-1000 square feet per 5 gallon pail) depending on the surface finish and porosity of the substrate.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003ePLANNING AND SURFACE PREP\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 25% Sealer can be applied to concrete that is at least 28 days old. Finish trowel the concrete and allow surface water to dissipate completely. Use a low pressure sprayer (20 - 30 lbs.) and apply a uniform coat at a rate of coverage as specified below. Avoid heavy accumulations. A second coat may be necessary where concrete is very porous and where absorption is very rapid. An additional coat may be applied after first coat is tack free.\u003c\/p\u003e\n\u003cp\u003eBroomed Concrete - 250-350 square feet per gallon.\u003c\/p\u003e\n\u003cp\u003eTroweled Concrete - 300-450 square feet per gallon.\u003c\/p\u003e\n\u003cp\u003eDustproof Seal - 250-400 square feet per gallon.\u003c\/p\u003e\n\u003cp\u003eSecond Coat - 300-600 square feet per gallon.\u003c\/p\u003e\n\u003cp\u003e\u003ci\u003e(These coverage rates are approximations only. Many factors will affect coverage rates.  These will include, but are not limited to: surface texture, porosity of the concrete, and weather conditions.)\u003c\/i\u003e\u003c\/p\u003e\n\u003cp\u003eCLEAN AND DRY: AC the art of concrete 25% Sealer may be applied on fully cured concrete. All surfaces must be clean and free of all contaminants such as dust, dirt, oils, efflorescence, grease, paint, glue, rust, algae, mildew, non-acrylic coatings and any other foreign matter that may be a bond breaker. Allow 24 hours for the substrate to dry before applying.\u003c\/p\u003e\n\u003cp\u003eSURFACE CONDITION: All concrete substrates should be sound with no hollow spots, scaling or flaking.  All delaminated material should be completely removed. Shot blasting, grinding and\/or scarifying should be done in those areas.\u003c\/p\u003e\n\u003cp\u003eMASKING: All areas that are not intended to receive AC the art of concrete 25% Sealer, should be protected by masking. Protect vegetation and landscaping.\u003c\/p\u003e\n\u003cp\u003eTOUCH-UP: Finish all touch-up work prior to sealing. This includes cleaning, detailing and colouring.\u003c\/p\u003e\n\u003cp\u003ePLANNING: The substrate must be dry for all steps, during and 24 hours after application. Application of AC the art of concrete 25% Sealer should be avoided on extremely cold or hot days (if the temperature will not be within the aforementioned ranges for 12-24 hours after application). Do not apply if rain, snow or hail is being forecast for the 24 hour period after application.\u003c\/p\u003e\n\u003cp\u003eBoth the concrete and the ambient air temperature should be between 10°C and 32°C during application.\u003c\/p\u003e\n\u003cp\u003eMIXING: This product does not need mixing. It is ready for use and no dilution is necessary.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eAPPLICATION: \u003c\/b\u003eAC the art of concrete 25% Sealer will darken concrete.\u003c\/p\u003e\n\u003cp\u003eROLLING:\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eUse a bucket grid or metal paint tray to ensure application of a thin film. (No puddling of product)\u003c\/li\u003e\n\u003cli\u003eRoller sleeves will require a solvent resistant core.\u003c\/li\u003e\n\u003cli\u003eThickness of roller sleeve will depend on the substrate being covered. A rougher surface will require a longer nap. A smooth cementitious surface such as a garage floor will require a 6 mil roller sleeve. Broom finished concrete, light exposed aggregate or a shallow stamped concrete will require a 10 mill roller sleeve. Deep exposed aggregate or a deep stamped concrete will require a 19 mil roller sleeve.\u003c\/li\u003e\n\u003cli\u003eBack rolling will help to eliminate roller lines. Back rolling should be done perpendicular to application.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eSPRAYING:\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eUse a low pressure sprayer (20 - 30 lbs.) and apply a uniform coat at a rate of coverage as specified below. Avoid heavy accumulations. A second coat may be necessary where concrete is very porous and where absorption is very rapid. An additional coat may be applied after first coat is tack free.\u003c\/li\u003e\n\u003cli\u003eA single coat is usually sufficient for most applications. However, if your substrate looks “blotchy or uneven” after the first coat, a second coat may be applied. Wait for the first coat to dry sufficiently so that you may walk on it. If a second coat is required, it can be applied exactly as the first coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003ePlease allow the proper amount of cure time after applying sealer. For foot traffic allow 24 hours. For vehicular traffic allow 72 hours.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCLEAN UP:\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eBefore AC the art of concrete 25% Sealer dries, solvents such as Xylene or Acetone may be used.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eSTORAGE AND CAUTIONS:\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 25% Sealer is flammable. Avoid heat sources, spark, electric tools and open flame sources. Store in a cool dry area out of direct sunlight. Shelf life under normal recommended conditions is 2 years. Store in sealed containers. Keep area well ventilated. Do not allow to freeze. \u003cb\u003eINHALATION: \u003c\/b\u003eUse approved NIOSH PPE (Respirator for organic vapours). \u003cb\u003eSKIN CONTACT: \u003c\/b\u003eMay cause irritation.  Remove all contaminated clothing and wash before reusing. Wash affected skin area with soap and water. If symptoms persist, seek medical attention.  \u003cb\u003eEYE CONTACT: \u003c\/b\u003eWear eye protecting while handling product. If contact with eyes does occur, remove contact lenses (if present). Flush eyes with water or eye wash solution for 15 minutes. Seek medical Attention.  Consult the SDS sheets for further information before use of product. \u003cb\u003eKEEP OUT OF REACH OF CHILDREN.\u003c\/b\u003e\u003c\/p\u003e\n\u003cp class=\"MsoNormal\"\u003eThis Product is classified as a Hazardous Materials and needs to be shipped according to the Transportation of Dangerous Goods (TDG) shipping regulations. Because of this, extra shipping charges will be assessed due to the TDG services needed.  This product will have to be shipped on an LTL carrier that has the capabilities to carry out this service.  You will be contacted with the extra charges needed. \u003c\/p\u003e\n\u003cp\u003e DATA SHEET DOWNLOADS\u003c\/p\u003e\n\u003cp\u003e\u003ca rel=\"noopener\" href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0681\/0737\/0788\/files\/AC_25_Contractor_Grade_Sealer_400GPL_TDS.pub?v=1744898597\" target=\"_blank\"\u003eAC - the art of concrete 25% Sealer TDS\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca rel=\"noopener\" href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0681\/0737\/0788\/files\/AC_25_Contractor_Grade_Sealer_400GPL_SDS.docx?v=1744898597\" target=\"_blank\"\u003eAC - the art of concrete 25% Cure \u0026amp; Seal SDS\u003c\/a\u003e\u003c\/p\u003e","brand":"AC the art of concrete","offers":[{"title":"Default Title","offer_id":48134465290532,"sku":"**209146","price":59.29,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0681\/0737\/0788\/files\/ACContractor251Gallon.jpg?v=1716306132"},{"product_id":"ac-the-art-of-concrete-30-contractor-grade-1-gallon","title":"AC - the art of concrete 30 Percent Sealer 1 Gallon","description":"\u003cp\u003e\u003cb\u003ePRODUCT DESCRIPTION AND USES\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 30% Sealer is a VOC Compliant, premium high quality, durable, abrasion resistant, single component 30% acrylic solids sealer for new or existing concrete and masonry. The 30% solids content provides a UV stable high-gloss finish that will colour enhance the concrete surface. AC the art of concrete 30% Sealer  is ideal for use on concrete that is at least 28 days old. This product may be used on all concrete no matter the finish. Concrete may be smooth or rough finished and may include:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eConcrete Flatwork\u003c\/li\u003e\n\u003cli\u003eLight Commercial\u003c\/li\u003e\n\u003cli\u003eArchitectural Concrete\u003c\/li\u003e\n\u003cli\u003eBrick\u003c\/li\u003e\n\u003cli\u003eStone\u003c\/li\u003e\n\u003cli\u003ePrecast concrete \u0026amp; walls\u003c\/li\u003e\n\u003cli\u003eResidential walkways, driveways and patios\u003c\/li\u003e\n\u003cli\u003eConcrete curbing and borders\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003ePACKAGING\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 30% Sealer is available in 18.9L containers and is a ready to use formulation.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCOVERAGE\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 30% Sealer will cover 150 - 200 square feet per gallon. (700-1000 square feet per 5 gallon pail) depending on the surface finish and porosity of the substrate.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003ePLANNING AND SURFACE PREP\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 30% Sealer can be applied to concrete that is at least 28 days old. Finish trowel the concrete and allow surface water to dissipate completely. Use a low pressure sprayer (20 - 30 lbs.) and apply a uniform coat at a rate of coverage as specified below. Avoid heavy accumulations. A second coat may be necessary where concrete is very porous and where absorption is very rapid. An additional coat may be applied after first coat is tack free.\u003c\/p\u003e\n\u003cp\u003eBroomed Concrete - 250-350 square feet per gallon.\u003c\/p\u003e\n\u003cp\u003eTroweled Concrete - 300-450 square feet per gallon.\u003c\/p\u003e\n\u003cp\u003eDustproof Seal - 250-400 square feet per gallon.\u003c\/p\u003e\n\u003cp\u003eSecond Coat - 300-600 square feet per gallon.\u003c\/p\u003e\n\u003cp\u003e\u003ci\u003e(These coverage rates are approximations only. Many factors will affect coverage rates.  These will include, but are not limited to: surface texture, porosity of the concrete, and weather conditions.)\u003c\/i\u003e\u003c\/p\u003e\n\u003cp\u003eCLEAN AND DRY: AC the art of concrete 30% Sealer may be applied on fully cured concrete. All surfaces must be clean and free of all contaminants such as dust, dirt, oils, efflorescence, grease, paint, glue, rust, algae, mildew, non-acrylic coatings and any other foreign matter that may be a bond breaker. Allow 24 hours for the substrate to dry before applying.\u003c\/p\u003e\n\u003cp\u003eSURFACE CONDITION: All concrete substrates should be sound with no hollow spots, scaling or flaking.  All delaminated material should be completely removed. Shot blasting, grinding and\/or scarifying should be done in those areas.\u003c\/p\u003e\n\u003cp\u003eMASKING: All areas that are not intended to receive AC the art of concrete 30% Sealer, should be protected by masking. Protect vegetation and landscaping.\u003c\/p\u003e\n\u003cp\u003eTOUCH-UP: Finish all touch-up work prior to sealing. This includes cleaning, detailing and colouring.\u003c\/p\u003e\n\u003cp\u003ePLANNING: The substrate must be dry for all steps, during and 24 hours after application. Application of AC the art of concrete 30% Sealer should be avoided on extremely cold or hot days (if the temperature will not be within the aforementioned ranges for 12-24 hours after application). Do not apply if rain, snow or hail is being forecast for the 24 hour period after application.\u003c\/p\u003e\n\u003cp\u003eBoth the concrete and the ambient air temperature should be between 10°C and 32°C during application.\u003c\/p\u003e\n\u003cp\u003eMIXING: This product does not need mixing. It is ready for use and no dilution is necessary.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eAPPLICATION: \u003c\/b\u003eAC the art of concrete 30% Sealer will darken concrete.\u003c\/p\u003e\n\u003cp\u003eROLLING:\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eUse a bucket grid or metal paint tray to ensure application of a thin film. (No puddling of product)\u003c\/li\u003e\n\u003cli\u003eRoller sleeves will require a solvent resistant core.\u003c\/li\u003e\n\u003cli\u003eThickness of roller sleeve will depend on the substrate being covered. A rougher surface will require a longer nap. A smooth cementitious surface such as a garage floor will require a 6 mil roller sleeve. Broom finished concrete, light exposed aggregate or a shallow stamped concrete will require a 10 mill roller sleeve. Deep exposed aggregate or a deep stamped concrete will require a 19 mil roller sleeve.\u003c\/li\u003e\n\u003cli\u003eBack rolling will help to eliminate roller lines. Back rolling should be done perpendicular to application.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eSPRAYING:\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eUse a low pressure sprayer (20 - 30 lbs.) and apply a uniform coat at a rate of coverage as specified below. Avoid heavy accumulations. A second coat may be necessary where concrete is very porous and where absorption is very rapid. An additional coat may be applied after first coat is tack free.\u003c\/li\u003e\n\u003cli\u003eA single coat is usually sufficient for most applications. However, if your substrate looks “blotchy or uneven” after the first coat, a second coat may be applied. Wait for the first coat to dry sufficiently so that you may walk on it. If a second coat is required, it can be applied exactly as the first coat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003ePlease allow the proper amount of cure time after applying sealer. For foot traffic allow 24 hours. For vehicular traffic allow 72 hours.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCLEAN UP:\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eBefore AC the art of concrete 30% Sealer dries, solvents such as Xylene or Acetone may be used.\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eSTORAGE AND CAUTIONS:\u003c\/b\u003e\u003c\/p\u003e\n\u003cp\u003eAC the art of concrete 30% Sealer is flammable. Avoid heat sources, spark, electric tools and open flame sources. Store in a cool dry area out of direct sunlight. Shelf life under normal recommended conditions is 2 years. Store in sealed containers. Keep area well ventilated. Do not allow to freeze. \u003cb\u003eINHALATION: \u003c\/b\u003eUse approved NIOSH PPE (Respirator for organic vapours). \u003cb\u003eSKIN CONTACT: \u003c\/b\u003eMay cause irritation.  Remove all contaminated clothing and wash before reusing. Wash affected skin area with soap and water. If symptoms persist, seek medical attention.  \u003cb\u003eEYE CONTACT: \u003c\/b\u003eWear eye protecting while handling product. If contact with eyes does occur, remove contact lenses (if present). Flush eyes with water or eye wash solution for 15 minutes. Seek medical Attention.  Consult the SDS sheets for further information before use of product. \u003cb\u003eKEEP OUT OF REACH OF CHILDREN.\u003c\/b\u003e\u003c\/p\u003e\n\u003cp class=\"MsoNormal\"\u003eThis Product is classified as a Hazardous Materials and needs to be shipped according to the Transportation of Dangerous Goods (TDG) shipping regulations. Because of this, extra shipping charges will be assessed due to the TDG services needed.  This product will have to be shipped on an LTL carrier that has the capabilities to carry out this service.  You will be contacted with the extra charges needed. \u003c\/p\u003e\n\u003cp\u003e DATA SHEET DOWNLOADS\u003c\/p\u003e\n\u003cp\u003e\u003ca rel=\"noopener\" href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0681\/0737\/0788\/files\/AC_30_Contractor_Grade_Sealer_400GPL_TDS.pub?v=1744898768\" target=\"_blank\"\u003eAC - the art of concrete 30% Sealer TDS\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca rel=\"noopener\" href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0681\/0737\/0788\/files\/AC_30_Contractor_Grade_Sealer_400GPL_SDS.docx?v=1744898768\" target=\"_blank\"\u003eAC - the art of concrete 30% Cure \u0026amp; Seal SDS\u003c\/a\u003e\u003c\/p\u003e","brand":"AC the art of concrete","offers":[{"title":"Default Title","offer_id":48134466732324,"sku":"**220990","price":63.29,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0681\/0737\/0788\/files\/ACContractor301Gallon.jpg?v=1716327436"}],"url":"https:\/\/hardrockconcretesupplies.com\/collections\/ac-the-art-of-concrete-sealer.oembed","provider":"Hard Rock Concrete Supplies","version":"1.0","type":"link"}