SureCrete’s WallStamp is a concrete wall stamp overlay mix that is stampable and also carvable. Special formulated for applying on a vertical surface with little to no slumping or sagging at 3/4 inch. Add color to enhance depth and design.

SureCrete's WallStamp™, a concrete wall stamp mix that is a lightweight, single component cement overlay designed for both interior and exterior vertical surfaces. When stamped the texture can resemble an array of designs: cut stone, random stone, brick, slate, etc. Alternatively, Wall Stamp may be textured and “cut” free-hand. It offers restoration, repair, resurfacing, and architectural accenting of existing vertical surfaces. Typical areas include retention walls, entry/accent walls, columns, gable ends, fireplace accents, and any other vertical surface or wall. Wall Stamp™ is formulated to provide excellent bonding to new as well as existing concrete, concrete block, ICF, polystyrene foam, drywall, plaster, plywood, and even painted surfaces.

WallStamp™, used in an incredibly diverse array of applications - everything from pre-made stamped texture patterns to custom carved theme park designs and sculptures. With its ability to have great adhesion qualities and decent work time, Wall Stamp provides an excellent alternative to casting conventional concrete on vertical surfaces, especially in regards to custom carving applications. Even if you don't have the artistic carving skills of a professional artisan, a homeowner can apply the Wall Stamp product without formal training, although we'd probably suggest the utilization of a textured stamping tool.

Wall Stamp Concrete Overlay Vertical application Abilities:

Faux Brick Patterns
Custom Carved Stone
Fire Places
Fire Surrounds
Retaining Walls
Vertical Concrete Overlay
Faux Brick Patterns
Custom Carved Stone
Fire Places
Fire Surrounds
Retaining Walls

How to Apply SureCrete WallStamp™ Vertical Stamping Overlay mix?

Wall Stamp has a wide variety of application methods:

Any surface receiving a cement overlay coating must be clean, cured, sound and profiled. See our Surface Preparation products for more information on accomplishing this
Make sure that temperatures will remain between 50 and 90 degrees Fahrenheit and there will be no precipitation in the applied areas for a 48 hour period following application.
Add 5 quarts water per 40 lb bag to 5 gal bucket and mix in any color desired for integral coloring of Wall Stamp
Slowly introduce Wall Stamp while continuously mixing and mix for a minimum of 1 minute once all product into a container.
Scrape the inside of the bucket to make sure there are no "dry pockets" of material that have not mixed properly.
A base coat is always suggested when using Wall Stamp.
If applying onto a surface other than concrete, the use of fiberglass mesh is required
Trowel a tight thin coat o the substrate, using as much force as can be achieved with a hand trowel.
Trowel 100% coverage, leaving no bare spots, a minimum of 1/8" material.
Base coat must not be completely dry or it must be scratched prior to finish coat application.
Wall Stamp may be applied in multiple lifts up to 1/2" thick at a time.
As finish coat begins to dry, yielding to one's finger without sticking, it may be tooled in a variety of ways. How you do it is up to you!
Once the surface is dry to the touch, it can accept stains and secondary colorants at this point, and is also ready to receive a sealer. Typical applications would utilize an acrylic sealer such as SureSeal Super 20 or Super WB.

Frequently Asked Questions About Wall Stamp Overlay Mix:

Do I have to use a fiberglass mesh?

Although any use of mesh will increase strength, required across non-concrete surfaces or concrete surfaces that are cracked and unsound.

Is there a limit to how far I can build out Wall Stamp?

Technically yes, but only while it is still workable – at about 3″, the level of the slump will out the weight it’s adhesive properties. And of course, you must always consider the product placed on the substrate by adding more Wall Stamp™.

Can I mix Wall Stamp to great batches?

While mixing large batches can be done, it is important never to mix up more than can be applied within a 45-minute time frame.

Specs and Properties of Wall Stamp:

Coverage Approx 18 square foot @ 3/8″ (Varies based on substrate and application)
VOC Rating 0 g/L
Shelf Life 1 year in original unopened container
Mixing Ratio 5-6 quarts water per 40 lb bag
Base Color Light Gray
Density 118 lbs/cubic foot
Compressive Strength ASTM C-109: 2,600 PSI @28 days
Flexural Strength ASTM C-348: 950 PSI @ 28 days
Tensile Strength ASTM C-190: 140 PSI @ 28 days
Abrasion Resistance 28 days %loss – 500 cycles – less than 0.40%
Mosaic Shear ANSI A 118.4: 275 PSI @ 28 days
Water Permeability ASTM D2247: Passes Freeze/Thaw @ 50 cycles

DATA SHEET DOWNLOADS

Wallstamp Brochure

Wall Stamp TDS

Wall Stamp SDS

Wall Stamp Overlay Video

FILTERS

Copyright © Hard Rock Concrete Supplies. all rights reserved.

Wishlist

Wishlist

Compare